Latex gloves, extra long

prices inc VAT
5,22 EUR
( inc VAT | ex VAT )

from 12 pair: 4,63

from 36 pair: 4,39

from 144 pair: 4,03

Catalogue No.: 7611477
Delivery time approx. 2-3 working
days
Note

The quoted delivery time in working days does not include weekends or bank holidays. The delivery date of the goods depends on the selected payment type.

Deliveries against prepayment usually be delivered on working days (Monday to Friday) once payment has been received.

Deliveries on account, or direct debit, PayPal, credit card and COD order usually be delivered on working days (Monday to Friday) once the order has been received.

If the goods are embroidered, printed or designed in any way to your specifications, the delivery date will be agreed separately for the specific order.

  • EN 388:2016, Mechanical risks 3131X
  • EN ISO 374-1:2016 - TYPE B, resistant to Chemicals, AKL
  • EN ISO 374-5:2016, Chemicals and Micro Organisms
  • EN 407:2004, Thermal risks, X2XXXX
  • Seamless, extra thick latex coating
  • Palm of hand in cotton
  • Thanks to extra long back, highly suitable for handling wet goods
  • roughened surface for good grip
  • Areas of application: Tried and tested and recommended for handling highly abrasive and sharp-edged parts (concrete stone, plaster, construction steel, sheet metal etc.)
  • Length: approx. 33 cm
Microorganisms
Microorganisms EN ISO 374-5:2016

It is usually assumed that protection gloves that withstand penetration in the test, offer effective protection against bacteria and fungi. However, because many viruses are much smaller than bacteria and fungi, these protection gloves may offer inadequate protection in practical fields.


A protection glove that is resistant to bacteria is a watertight glove that has a maximum AQL value of 1.5 in the permeability test. The AQL value (AQL = Acceptable Quality Level) reflects a given limit or the minimum quality requirement.


In general, the lower the AQL value, the better the quality of the protection gloves.



Protection against microorganisms:

Gloves that protect against bacteria and fungi. Not tested against viruses.

Mechanical risks
Mechanical risks EN 388:2016

Protection gloves of this standard need to protect against physical and mechanical loads such as wear, cuts, puncturing, tearing or felling cuts. These loads can occur when working with metal or wood or any other tasks where hands need to be protected against mechanical injury. Also, they must comply with the regulations relating to electrical conductivity of protection gloves.


Protection gloves for mechanical risks must satisfy at least one of the test criteria listed in the table.


Testing Criteria:

Abrasion Resistance: 0-4

Cut Resistance: 0-4

Tear Resistance: 0-4

Puncture Resistance: 0-4

EN-ISO cut resistance: A-F

EN impact protection: yes/no


The higher the number (shown with an X below the icon in the example), the better the test result.

Thermal risks
Thermal risks EN 407:2004

One faces a number of thermal risks at work. For the protection effect of the gloves it is important to differentiate between ambient heat or direct contact with hot objects. Risks are also involved when faced with extreme heat caused by fires, radiation etc.


Heat protection gloves should have wear resistance properties and also a certain level of cut resistance. The minimum wear and tear resistance according to EN 388 is specified for protection gloves of the EN 407.


Fire-resistant and heat-resistant protection gloves from engelbert strauss offer day-to-day safety at work.


Testing Criteria:

Flammability: 0-4

Contact Heat Resistance: 0-4

Convective Heat Resistance: 0-3

Radiant Heat Resistance: 0-4

Resistance to small drops of molten metal: 0-4

Resistance to large quantities of molten metal: 0-4


The higher the number (shown with an X below the icon in the example), the better the test result.

EN ISO 374-1:2016 TYP B

Full chemical protection gloves primarily aim to protect the hands against chemicals. They are assigned to the PSA Category III. Due to the infinite range of chemicals, there is no one specific glove that will offer protection against all liquids. Instead, the best product must be selected for the task at hand. Full chemical protection has a protection index of at least 2, i.e. a permeation time > 30 minutes for at least 3 of 12 statutory defined test chemicals. (Permeation = penetration on a molecular level).

Gloves marked with a conical flask offer full chemical protection. The chemicals against which the gloves offer protection are identified with a letter below the pictogram.


TYPE B

Permeation performance at least level 2, >30 minutes against at least three chemicals in the list:


Testing Criteria:

A- Methanol

B- Acetone

C- Acetonitrite

D- Di-chloromethane

E- Carbon disulphide

F- Tuluol

G- Diethylamine

H- Tetrahydrofuran

I- Ethyl acetate

J- N-Heptane

K- Sodium hydroxide 40 %

L- Sulphuric acid 96 %

M- Nitric acid 65%

N- Acetic acid 99 %

O- Ammonium hydroxide 25 %

P- Hydrogen peroxide 30 %

S- Hydrofloric acid 40 %

T- Formaldehyde 37 %

Latex coating
  • good wet grip
  • flexible and elastic
  • waterproof
  • for medium to heavy-duty work